Skip to main content
Version: 3.2

Install Portworx with Pure Storage FlashArray enabled with secure multi-tenancy

Prerequisites​

  • Have an on-premise Kubernetes cluster with FlashArray that meets the minimum requirements for Portworx.
  • Have a Pure Storage FlashArray with Purity version 6.6.11 or newer.
  • Use the FC, iSCSI, or NVMe/RoCE protocol.
  • Create a Pure secret px-pure-secret under the same namespace as Storage Cluster before installing Portworx.
  • Enable CSI for Portworx.
  • Install the latest Linux multipath software package on your operating system that include these fixes. This package also must include kpartx.
  • Have the latest Filesystem utilities/drivers.
  • Have the following latest package installed on all nodes (including master):
    • libStorageMgmt
    • device-mapper-multipath
    • libstoragemgmt-udev
    • iscsi-initiator-utils
    note

    Red Hat only: Ensure that the second action CAPACITY_DATA_HAS_CHANGED is uncommented in the 90-scsi-ua.rules file and you have restarted the udev service.

  • Have the latest FC initiator software for your operating system (Optional; required for FC connectivity).

Configure your physical environment​

Before you install Portworx, ensure that your physical network is configured appropriately and that you meet the prerequisites. You must provide Portworx with your FlashArray configuration details during installation.

  • Each FlashArray management IP address can be accessed by each node.
  • Your cluster contains an up-and-running FlashArray with an existing dataplane connectivity layout (iSCSI, Fibre Channel).
  • If you're using iSCSI, the storage node iSCSI initiators are on the same VLAN as the FlashArray iSCSI target ports.
  • If you are using multiple network interface cards (NICs) to connect to an iSCSI host, then all of them must be accessible from the FlashArray management IP address.
  • If you're using Fibre Channel, the storage node Fibre Channel WWNs have been correctly zoned to the FlashArray Fibre Channel WWN ports.
  • You have an API token for a user on your FlashArray with at least storage_admin permissions. Check the documentation on your device for information on generating an API token.

(Optional) Set iSCSI interfaces on FlashArray​

If you are using iSCSI protocol, you can its interfaces on FlashArray using the following steps:

  1. Run the following command to get the available iSCSI interface within your environment: 
    iscsiadm -m iface
    You can use the output in the next step.
  2. Run the following command to specify which network interfaces on the FlashArray system are allowed to handle iSCSI traffic. Replace <interface-value> by the value you retried in the previous step: 
    pxctl cluster options update --flasharray-iscsi-allowed-ifaces <interface-value>

Configure your software environment​

Configure your software environment within a computing infrastructure. It involves preparing both the operating system and the underlying network and storage configurations.

Follow the instructions below to set up CSI snapshot feature, disable secure boot mode, and configure the multipath.conf file appropriately. These configurations ensure that the system's software environment is properly set up to allow Portworx to interact correctly with the hardware components, like storage devices (using protocols such as iSCSI or Fibre Channel), and to function correctly within the network infrastructure.

Set up your environment to use CSI snapshot feature​

To use the CSI snapshot feature, install the following:

  • Snapshot V1 CRDs

  • Snapshot controller

    • You can also install the snapshot controller by adding the following lines to your StorageCluster:

        csi:
          enabled: true
          installSnapshotController: true

Disable secure boot mode​

Portworx requires the secure boot mode to be disabled to ensure it can operate without restrictions. Here's how to disable secure boot mode across different platforms:

For REHL/CentOS you can perform the following steps to check and disable the secure boot mode:

  1. Check the status of secure boot mode:

    /usr/bin/mokutil --sb-state

  2. If secure boot is enabled, disable it:

    /usr/bin/mokutil --disable-validation

  3. Apply changes by rebooting your system:

    reboot

Verify the status of the secure boot mode​

Run the following command to ensure that the secure boot mode is off:

/usr/bin/mokutil --sb-state
SecureBoot disabled

Configure the multipath.conf file​

  • For defaults:
    • FlashArray and Portworx does not support user friendly names, disable it and set it to no before installing Portworx on your cluster. This ensures Portworx and FlashArray use consistent device naming conventions.
    • Add polling 10 as per the RHEL Linux recommended settings. This defines how often the system checks for path status updates.
  • To prevent any interference from multipathd service on Portworx volume operations, set the pxd device denylist rule.

Your multipath.conf file should resemble the following structure:

defaults {
  user_friendly_names no
  enable_foreign "^$"
        polling_interval    10
}

devices {
    device {
        vendor                      "NVME"
        product                     "Pure Storage FlashArray"
        path_selector               "queue-length 0"
        path_grouping_policy        group_by_prio
        prio                        ana
        failback                    immediate
        fast_io_fail_tmo            10
        user_friendly_names         no
        no_path_retry               0
        features                    0
        dev_loss_tmo                60
        find_multipaths             yes
    }
    device {
        vendor                   "PURE"
        product                  "FlashArray"
        path_selector            "service-time 0"
        hardware_handler         "1 alua"
        path_grouping_policy     group_by_prio
        prio                     alua
        failback                 immediate
        path_checker             tur
        fast_io_fail_tmo         10
        user_friendly_names      no
        no_path_retry            0
        features                 0
        dev_loss_tmo             600
        find_multipaths          yes
    }
}

blacklist_exceptions {
        property "(SCSI_IDENT_|ID_WWN)"
}

blacklist {
      devnode "^pxd[0-9]*"
      devnode "^pxd*"
      device {
        vendor "VMware"
        product "Virtual disk"
      }
}

Apply Multipath and Udev configs​

Use a MachineConfig in OpenShift to apply multipath and udev configuration files consistently across all nodes.

  1. Convert the configuration files to base64 format and add them to the MachineConfig, as shown in the following example:

    apiVersion: machineconfiguration.openshift.io/v1
    kind: MachineConfig
    metadata:
      creationTimestamp:
      labels:
        machineconfiguration.openshift.io/role: worker
      name: <your-machine-config-name>
    spec:
      config:
        ignition:
          version: 3.2.0
        storage:
          files:
          - contents:
              source: data:,<base64-encoded-multipath-conf>
            filesystem: root
            mode: 0644
            overwrite: true
            path: /etc/multipath.conf
          - contents:
              source: data:,<base64-encoded-udev_conf>
            filesystem: root
            mode: 0644
            overwrite: true
            path: /etc/udev/rules.d/99-pure-storage.rules
        systemd:
          units:
          - enabled: true
            name: iscsid.service
          - enabled: true
            name: multipathd.service

  2. Apply the MachineConfig to your cluster:

    oc apply -f <your-machine-config-name>.yaml

Set up user access in FlashArray​

Follow this sections to set up user access for your FlashArray.

Create realms in FlashArray​

When multiple clusters are attached to a FlashArray, it's essential to define specific realms for organizing and separating storage. When multiple clusters are attached to a FlashArray, admin can specify the realm, and FlashArray volumes from Portworx install will be placed inside the realm. This way different users having access to the array and cluster, can only see their storage volumes. This method is particularly useful in multi-tenant environments where different customers share the same FlashArray.

To set up realms for different customers, follow these steps as an admin:

  1. Create a realm for each customer. All volumes from the Portworx installation will be placed within this realm, ensuring customer-specific data isolation: 
    purerealm create <customer1-realm>
    Name                Quota Limit
    <customer1-realm>   -
  2. A pod in FlashArray defines a boundary where specific volumes are placed. Create a pod inside the realm you just defined: 
    purepod create <customer1-realm>::<fa-pod-name>
note

Stretched FlashArray pods (pods spanning multiple FlashArrays) are not supported.

By assigning realms and pods in a FlashArray, you can ensure that different users only interact with the specific storage resources allocated to them.

Create a realm policy​

After defining realms, you need to bind users to those realms by creating policies. Policies specify the level of access a user has within a realm. These policies ensure that users only have the necessary permissions to perform their tasks.

  1. Create a policy for a realm. Ensure that you have administrative privileges on FlashArray before proceeding. This policy grants users access to their respective realms with defined capabilities: 
    purepolicy management-access create --realm <customer1-realm> --role storage --aggregation-strategy all-permissions <realm-policy>
    For basic privileges, use the following command: 
    purepolicy management-access create --realm <customer1-realm> --role storage --aggregation-strategy least-common-permissions <realm-policy>

  2. Verify the created policy. This step ensures that the policy has been set up correctly with the right permissions: 
    purepolicy management-access list 
    Name             Type         Enabled  Capability  Aggregation Strategy      Resource Name    Resource Type  
    <realm-policy>  admin-access  True     all         all-permissions           <customer1-realm>  realms

This policy ensures that users linked to the specified realm can perform storage operations within their allocated realm.

Create users​

Once a policy is created, you need to create users who can access the FlashArray through that policy. These users will be bound to the realms and policies you previously configured, controlling their access and operations on the FlashArray.

Create a user linked to a policy. This command creates a user with the access rights defined by the policy. You must create a password that the user can use to log in to FlashArray, as shown in the output:

pureadmin create --access-policy <realm-policy> <flasharray-user>
Enter password: 
Retype password: 
Name               Type   Access Policy
<flasharray-user>  local  <realm-policy>

This step ensures that users are securely connected to their designated realms with appropriate access.

Generate an API Token​

An API token is essential for enabling secure communication between Portworx and FlashArray. The token serves as a key, authorizing Portworx to interact with the FlashArray on behalf of the user. It’s necessary to generate this token so that Portworx can authenticate and perform tasks like provisioning and managing storage.

Generate an API token for the user. This token is required for the user to authenticate with the FlashArray:

  • Sign in as the newly created user in the FlashArray CLI
  • Run pureadmin create --api-token and copy the created token. By completing these steps, you ensure that Portworx can securely manage storage resources within the FlashArray environment.

Create a JSON configuration file​

For Portworx to integrate with FlashArray, it requires a JSON configuration file containing essential information about the FlashArray environment. This file, typically named pure.json, includes the management endpoints and the newly generated API token.

  • Management endpoints: The management endpoints are URLs or IP addresses that Portworx will use to send API calls to FlashArray. Find these by going to Settings and selecting Network within your FlashArray dashboard. Note the IP addresses or hostnames of your management interfaces, usually identified by a vir prefix, indicating virtual interfaces. Now for one array you can add two comma separated management endpoints: flassharray endpoints
  • API token: Generated in the previous section.
  • Realm: Realms are the objects which define the boundaries of a tenant. When multiple FlashArrays are attached to a cluster, admin can specify the realm and FlashArray volumes from Portworx install will be placed inside the realm. This way different users having access to the array can only see their storage volumes. Only one realm is supported per cluster per array, which means you can't have the same Portworx deployment use two realms on the same array.

Use the above information to create JSON file. Below is a template for the configuration content, which you should populate with your specific information:

{
  "FlashArrays": [
    {
      "MgmtEndPoint": "<first-fa-management-endpoint1>",
      "APIToken": "<first-fa-api-token>",
      "Realm": "<first-fa-realm>"
    },
    {
      "MgmtEndPoint": "<second-fa-management-endpoint2>",
      "APIToken": "<second-fa-api-token>",
      "Realm": "<second-fa-realm>"
    },
    ...
  ]
}

Create a Kubernetes Secret​

The specific name px-pure-secret is required so that Portworx can correctly identify and access the Kubernetes secret upon startup. This secret securely stores the FlashArray configuration details and allows Portworx to access this information within the Kubernetes environment.

Enter the following kubctl create command to create a Kubernetes secret called px-pure-secret:

oc create secret generic px-pure-secret --namespace <stc-namespace> --from-file=pure.json
secret/px-pure-secret created

Verify the iSCSI Connection with FlashArray​

The instructions in this section are using iSCSI network.

  1. Run the following command to discover your iSCSI targets. Replace <flash-array-interface-endpoint> with your FlashArray's interface, as shown in the following screenshot: Flash Array interface
iscsiadm -m discovery -t st -p <flash-array-interface-end-point>
10.13.xx.xx0:3260,207 iqn.2010-06.com.purestorage:flasharray.xxxxxxx
10.13.xx.xx1:3260,207 iqn.2010-06.com.purestorage:flasharray.xxxxxxx
  1. Verify that each node has a unique initiator. Run the following command on each node:
cat /etc/iscsi/initiatorname.iscsi
InitiatorName=iqn.1994-05.com.redhat:xxxxx
  1. If the initiator names are not unique, it's necessary to assign a new unique initiator name. To do this, execute the following command:
echo "InitiatorName=`/sbin/iscsi-iname`" > /etc/iscsi/initiatorname.iscsi

Replace the initiator names on any nodes that have duplicates with the newly generated unique names.

Once you've configured your environment and ensured that you meet the prerequisites, you're ready to deploy Portworx.

Generate specs​

To install Portworx with Kubernetes, you must first generate Kubernetes manifests that you will deploy in your cluster:

  1. Navigate to Portworx Central and log in, or create an account.

  2. In the Portworx section, select Get Started.

  3. On the Product Line page, choose any option depending on which license you intend to use, then click Continue to start the spec generator.

  4. In the Generate Spec page:

    1. Select 3.2 or newer from the Portworx Version dropdown.
    2. For Platform, select Pure FlashArray.
    3. Select None for Distribution Name, then click Customize at the bottom of Summary section.
    4. Navigate to the Storage window, select the checkbox for Enable multitenancy in the Configure Storage Devices section, and enter a FlashArray pod name in the Pure FA Pod Name field.
    5. By default, iSCSI is set as your protocol for data transfer. Select a different option from the Select type of storage area network dropdown.
    6. Click Next to complete the spec gen flow and click Finish to generate the specs.
    note

    By default, iSCSI is set as your protocol for data transfer. To change this option, click Customize and navigate to the Storage window. Select a different option from the Select type of storage area network dropdown.

  5. (Optional) If you are using multiple NICs for iSCSI host, then add the following environment variable to your StorageCluster spec. Replace <nic-interface-names> with comma-separated names of NICs such as "eth1,eth2":

    env:
    - name: flasharray-iscsi-allowed-ifaces
      value: "<nic-interface-names>"
note

If you have multiple NICs on your virtual machine, then FlashArray does not distinguish the NICs that include iSCSI and the others without iSCSI. This list must be provided, otherwise Portworx may potentially use only one of the provided interfaces.

Choose your deployment​

Depending on the whether you want to deploy Portworx with FlashArray to provide cloud storage or direct access volumes, click the appropriate tab:

Modify the spec​

Modify the cloudStorage section of the spec to include FlashArray pod information. This ensures that when Portworx is deployed, and it will create volumes in the pods within the realm for a particular user:

cloudStorage:
  deviceSpecs:                               
  - size=150,pod=<fa-pod-name>

Replace <fa-pod-name> with the FlashArray pod name defined in this section.

Apply specs​

Apply the Operator and StorageCluster specs you generated in the section above using the oc apply command:

  1. Deploy the Operator:

    oc apply -f 'https://install.portworx.com/<version-number>?comp=pxoperator&kbver=1.25.0&ns=portworx'
    serviceaccount/portworx-operator created
    podsecuritypolicy.policy/px-operator created
    clusterrole.rbac.authorization.k8s.io/portworx-operator created
    clusterrolebinding.rbac.authorization.k8s.io/portworx-operator created
    deployment.apps/portworx-operator created

  2. Deploy the StorageCluster:

    oc apply -f 'https://install.portworx.com/<version-number>?operator=true&mc=false&kbver=1.25.0&ns=portworx&b=true&iop=6&c=px-cluster-17efb9e2-xxx-xxx&stork=true&csi=true&mon=true&tel=true&st=k8s&promop=true'
    storagecluster.core.libopenstorage.org/px-cluster-17efb9e2-xxx-xxx created

Once deployed, Portworx detects that the FlashArray secret is present when it starts up and can use the specified FlashArray volumes.

Last updated on
Was this page helpful?