Prerequisites in FlashArray
Environment Prerequisites
The minimum supported size for a Portworx cluster is three nodes. Each node must meet the following hardware and software requirements:
Hardware | |
---|---|
CPU | 4 cores minimum, 8 cores recommended |
RAM | 4GB minimum, 8GB recommended |
Disk
|
|
Backing drive | 8GB (minimum required) 128 GB (minimum recommended) |
Operating system root partition | 64 GB is the minimum required size for the root filesystem which contains the operating system 128 GB minimum recommended |
Storage drives | Storage drives must be unmounted block storage: raw disks, drive partitions, LVM, or cloud block storage. |
Network connectivity | Bandwidth:
Latency requirements for synchronous replication: less than 10ms between nodes in the cluster |
Node type | Bare metal and virtual machine (VM) |
Software | |
---|---|
Linux kernel and distro | Kernel version 3.10 or greater. To check if your Linux distro and kernel are supported, see Supported Kernels. |
Docker | Version 1.13.1 or greater. |
Key-value store | Portworx needs a key-value store to perform its operations. As such, install a clustered key-value database (kvdb ) with a three node cluster.You can also use Internal KVDB during installation. In this mode, Portworx will create and manage an internal key-value store (KVDB) cluster. If you plan of using your own KVDB, refer to KVDB for Portworx for details on recommendations for installing and configuring a KVDB cluster. |
Disable swap | Disable swap on all nodes that will run the Portworx software. Ensure that the swap device is not automatically mounted on server reboot. |
Network Time Protocol (NTP) | All nodes in the cluster should be in sync with NTP time. Any time drift between nodes can cause unexpected behaviour, impacting services. |
Portworx network requirements
Portworx runs as a pod in a Kubernetes cluster and uses specific ports for communication, data transfer, and telemetry.
- East-to-west
- Inbound
- Outbound
note
- Portworx also requires the following ports:
- An open KVDB port. For example, if you're using etcd externally, open port 2379.
- An open UDP port at 9002.
- For telemetry, open ports 9024, 12001, and 12002. Ensure you are running Portworx Operator version 23.7.0 or higher to configure the telemetry port:
- Portworx Versions 2.13.7 and Older: Open port 9024 specifically for telemetry.
- Portworx Versions 2.13.8 and Newer: Use port 9029 for telemetry.
Kubernetes | Description |
---|---|
9001 | Portworx management port [REST] |
9002 | Portworx node-to-node port [gossip]/UDP |
9003 | Portworx storage data port |
9004 | Portworx namespace [RPC] |
9012 | Portworx node-to-node communication port [gRPC] |
9013 | Portworx namespace driver [gRPC] |
9014 | Portworx diags server port [gRPC] |
9018 | Portworx kvdb peer-to-peer port [gRPC] |
9019 | Portworx kvdb client service [gRPC] |
9021 | Portworx gRPC SDK gateway [REST] |
9022 | Portworx health monitor [REST] |
9029 | Telemetry log uploader |
12002 | Telemetry phone home |
Kubernetes | Description |
---|---|
9001 | Portworx management port [REST] |
9021 | Portworx gRPC SDK gateway [REST] |
Portworx Enterprise supported Kubernetes versions
Before you install Portworx on Kubernetes, ensure that you're using a supported Kubernetes version:
note
K3s users: You must use CSI integration to generate/use PVCs.
- 3.1
- 3.0
- 2.13
Type | Supported Versions |
---|---|
Kubernetes On-prem |
|
Supported Kubernetes Version |
---|
1.23, 1.24, 1.25, 1.26, 1.27, 1.28 |
Supported Kubernetes Version |
---|
1.21, 1.22, 1.23, 1.24, 1.25, 1.26 |