Skip to main content
Version: 3.2

Open NFS ports

SharedV4 volumes utilize NFS services, and they therefore require specific open NFS ports to allow for communication between nodes in your cluster. Depending on how your cluster nodes are configured, your firewall may block some of these ports, or your NFS ports may differ from the defaults. To solve these issues, you may need to manually assign NFS ports and ensure that your firewall or ACL allows them to communicate.

Portworx supports the following types of ReadWriteMany volumes:

If a PersistentVolumeClaim (PVC) has ReadWriteMany (RWX) access mode, Portworx creates a sharedv4 service volume by default. Sharedv4 service volumes use NFSv4 by default, which means only port 2049 needs to be opened. However, sharedv4 volumes use NFSv3 by default. If your volumes use another port, see the Manually assign and open NFS ports section.

This document provides instructions for detecting and opening NFS ports according to various cluster configurations that you may have.

Prerequisites​

All of the use-cases in this document will require that the mandatory Portworx network port ranges are open between nodes in the cluster, as documented here.

Determine which ports to open​

First, check what the existing NFS port configuration is for your nodes to see if they need to be remapped.

Enter the following command to find which ports NFS is using on your node:

rpcinfo -p

SharedV4 volumes communicate on the following standard ports/services:

  • PortMapper: tcp/udp 111 (default on most Linux distributions)
  • NFSd: tcp/udp 2049 (default on most Linux distributions)
  • MountD: tcp/udp 20048 (depends on the Linux distribution)

If the ports listed from the above rpcinfo output on your nodes match these standard ports, proceed to Open standard NFS ports (most Linux distributions).

If the NFS ports on your OS do not match these ports, or your OS randomly chooses the ports for these services, proceed to Manually assign and open NFS ports.

Open standard NFS ports (most Linux distributions)​

If your Linux distribution uses the standard ports identified in the previous section, you do not need to manually assign any ports for NFS, but you may need to open them.

Ensure that your ports are open on any firewalls and your ACL by entering the following commands:

iptables -I INPUT -p tcp -m tcp --match multiport --dports 111,2049,20048 -j ACCEPT
iptables -I OUTPUT -p tcp -m tcp --match multiport --dports 111,2049,20048 -j ACCEPT

Once you've determined that your hosts are using the standard ports and that you have opened those ports, you can start using SharedV4 volumes.

Manually assign and open NFS ports​

For certain Linux distributions, the OS chooses the mountd port randomly every time the node reboots. To solve this, you must manually assign NFS ports, and how you accomplish this depends on your OS.

Only perform the steps in one of the following sections if one of the following is true:

  • The mountd port is not fixed (and not the standard port of 20048) and is chosen at random by your Linux distribution.
  • You wish to open a contiguous range of ports for Portworx and want to shift the default NFS ports to your Portworx port range.

In order to manually assign and open NFS ports, follow the steps in the section that applies for your OS.

Assign NFS ports on the RedHat family of Linux (RHEL, CentOS, Fedora, etc)​

  1. Modify the /etc/sysconfig/nfs file, uncommenting or adding the following fields and assigning the associated values:

    • LOCKD_TCPPORT=9023
    • LOCKD_UDPPORT=9024
    • MOUNTD_PORT=9025
    • STATD_PORT=9026

  2. Enter the following command to restart the NFS server:

    systemctl restart nfs-server

  3. Open the newly assigned NFS ports on your access control list:

    iptables -I INPUT -p tcp -m tcp --match multiport --dports 111,2049,9023,9025,9026 -j ACCEPT
    iptables -I OUTPUT -p tcp -m tcp --match multiport --dports 111,2049,9023,9025,9026 -j ACCEPT
    iptables -I INPUT -p udp -m udp --dport 9024  -j ACCEPT
    iptables -I OUTPUT -p udp -m udp --dport 9024  -j ACCEPT

Open NFS ports on Debian or Ubuntu Linux​

Debian 10 / Ubuntu​

  1. Modify the /etc/default/nfs-kernel-server file. Uncomment or add the RPCMOUNTDOPTS field and add the --port 9024 option to the value:

    ...
    RPCMOUNTDOPTS="--manage-gids --port 9024"

  2. Enter the following command to restart the mountd service:

    systemctl restart nfs-mountd.service

  3. Verify that the mountd service is running on the port that you configured by searching the output of rpcinfo -p:

    rpcinfo -p | grep 'tcp.*mountd'
    100005    1   tcp   9024  mountd
    100005    2   tcp   9024  mountd
    100005    3   tcp   9024  mountd

Debian 9 and lower​

  1. Modify the /run/sysconfig/nfs-utils file, uncommenting or adding the following fields and assigning the associated values:

    • RPCNFSDARGS=" 8 --port 9023": append the --port 9023 option to any existing values.
    • RPCMOUNTDARGS="--port 9024": add the --port 9024 option.
    • STATDARGS="--port 9025 --outgoing-port 9026": add the --port 9025 and --outgoing-port 9026 options.

  2. Enter the following commands to restart the NFS server:

    systemctl daemon-reload
    systemctl restart rpc-statd
    systemctl restart rpc-mountd
    systemctl restart nfs-server

  3. Open the newly assigned NFS ports on your access control list:

    iptables -I INPUT -p tcp -m tcp --match multiport --dports 111,2049,9023,9025,9026 -j ACCEPT
    iptables -I OUTPUT -p tcp -m tcp --match multiport --dports 111,2049,9023,9025,9026 -j ACCEPT
    iptables -I INPUT -p udp -m udp --dport 9024  -j ACCEPT
    iptables -I OUTPUT -p udp -m udp --dport 9024  -j ACCEPT

Open NFS ports on CoreOS​

The following sharedv4 NFS services run on a node when Portworx is installed with sharedv4 support:

  • portmapper
  • status
  • mountd
  • nfs and nfs_acl
  • nlockmgr

View these services and the ports they are using by entering the following command:

rpcinfo -p

By default, services like mountd and nlockmgr run on random ports and must be fixed to a specific port.

Configure nfs, nfs_acl, and lockd ports​

By default, the nfs-server.service configuration file is located under the following directory:

/usr/lib/systemd/system/nfs-server.service

  1. Check the status of the existing nfs-server.service:

    systemctl status nfs-server

  2. Copy the systemd unit file from the usr directory into the etc directory:

    cp /usr/lib/systemd/system/nfs-server.service /etc/systemd/system/nfs-server.service

  3. Open /etc/systemd/system/nfs-server.service in a text editor and, under the [Service] section, add the --port 9023 value to the ExecStart=/usr/sbin/rpc.nfsd key:

    [Service]
    Type=oneshot
    RemainAfterExit=yes
    ExecStartPre=/usr/sbin/exportfs -r
    ExecStart=/usr/sbin/rpc.nfsd --port 9023
    ExecStop=/usr/sbin/rpc.nfsd 0
    ExecStopPost=/usr/sbin/exportfs -au
    ExecStopPost=/usr/sbin/exportfs -f

  4. Update the lockd ports:

    echo 9027 > /proc/sys/fs/nfs/nlm_udpport
    echo 9028 > /proc/sys/fs/nfs/nlm_tcpport

  5. Ensure that the lockd manager ports persist over node reboots by creating a 100-nfs-ports.conf file under the /etc/sysctl.d/ folder and adding the ports to it:

    cat /etc/sysctl.d/100-nfs-ports.conf
    fs.nfs.nlm_tcpport = 9027
    fs.nfs.nlm_udpport = 9028

  6. Reload the systemd daemon and restart the nfs-server service:

    systemctl daemon-reload
    systemctl restart nfs-server

  7. Verify that the NFS services are running on the ports you configured by searching the output of rpcinfo -p:

    rpcinfo -p | grep nfs
    100003    3   tcp   9023  nfs
    100003    4   tcp   9023  nfs
    100227    3   tcp   9023  nfs_acl
    rpcinfo -p | grep nlock
    100021    1   udp   9027  nlockmgr
    100021    3   udp   9027  nlockmgr
    100021    4   udp   9027  nlockmgr
    100021    1   tcp   9028  nlockmgr
    100021    3   tcp   9028  nlockmgr
    100021    4   tcp   9028  nlockmgr

Configure mountd services​

  1. Check the status of the existing nfs-server.service:

    systemctl status nfs-mountd

  2. Copy the systemd unit file from /usr into /etc:

    cp /usr/lib/systemd/system/nfs-mountd.service /etc/systemd/system/nfs-mountd.service

  3. Open /etc/systemd/system/nfs-mountd.service in a text editor and, under the [Service] section, add the --port 9024 value to the ExecStart=/usr/sbin/rpc.mountd key:

    [Unit]
    ...

    [Service]
    Type=forking
    ExecStart=/usr/sbin/rpc.mountd --port 9024

  4. Reload the systemd daemon and restart the nfs-server service:

    systemctl daemon-reload
    systemctl restart nfs-server

  5. Verify that the NFS services are running on the ports you configured by searching the output of rpcinfo -p:

    rpcinfo -p | grep mountd
    100005    1   udp   9024  mountd
    100005    1   tcp   9024  mountd
    100005    2   udp   9024  mountd
    100005    2   tcp   9024  mountd
    100005    3   udp   9024  mountd
    100005    3   tcp   9024  mountd

Configure statd services​

  1. Check the status of the existing rpc-statd.service:

    systemctl status rpc-statd

  2. Copy the systemd unit file from the usr directory into the etc directory:

    cp /usr/lib/systemd/system/rpc-statd.service /etc/systemd/system/rpc-statd.service

  3. Open /etc/systemd/system/rpc-statd.service in a text editor and, under the [Service] section, add the --port 9025 and --outgoing-port 9026 value to the ExecStart=/usr/sbin/rpc.statd key:

    [Unit]
    ...

    [Service]
    Environment=RPC_STATD_NO_NOTIFY=1
    Type=forking
    PIDFile=/var/run/rpc.statd.pid
    ExecStart=/usr/sbin/rpc.statd --port 9025 --outgoing-port 9026

  4. Reload the systemd daemon and restart the rpc-statd service:

    systemctl daemon-reload
    systemctl restart rpc-statd

  5. Verify that the NFS services are running on the ports you configured by searching the output of rpcinfo -p:

    rpcinfo -p | grep status
    100024    1   udp   9025  status
    100024    1   tcp   9025  status

Open NFS ports on PhotonOS​

  1. Modify the /etc/default/nfs-utils file, adding parameters to assign ports to services:

    MOUNTD_OPTS="--port 9024"
    NFSD_OPTS="--port 9023"
    STATD_OPTS="--port 9025 --outgoing-port 9026"

  2. Add the /etc/modprobe.d/lockd.conf file to assign ports to the nlockmgr service and reconfigure runtime ports:

    cat > /etc/modprobe.d/lockd.conf << .
    options lockd nlm_tcpport=9027
    options lockd nlm_udpport=9028
    .

    sysctl -w fs.nfs.nlm_tcpport=9027 fs.nfs.nlm_udpport=9028

  3. Restart NFS services:

    systemctl daemon-reload
    systemctl restart nfs-server nfs-mountd rpc-statd

  4. Open up the ports 9001 to 9028 in the iptables firewall, then restart the service:

    # add Portworx ports 9001..9028 before "COMMIT"
    sed -i~ '/^COMMIT/i -A INPUT -p tcp -m multiport --dports 111,9001:9028 -j ACCEPT' \
      /etc/systemd/scripts/ip4save
    systemctl restart iptables

  5. Verify that the NFS services are running on the ports that you just configured:

    rpcinfo -p
    program vers proto   port  service
     100000    4   tcp    111  portmapper
     100000    3   tcp    111  portmapper
     100000    2   tcp    111  portmapper
     100000    4   udp    111  portmapper
     100000    3   udp    111  portmapper
     100000    2   udp    111  portmapper
     100005    1   udp   9024  mountd
     100005    1   tcp   9024  mountd
     100005    2   udp   9024  mountd
     100005    2   tcp   9024  mountd
     100005    3   udp   9024  mountd
     100005    3   tcp   9024  mountd
     100024    1   udp   9025  status
     100024    1   tcp   9025  status
     100003    3   tcp   9023  nfs
     100003    4   tcp   9023  nfs
     100021    1   udp   9027  nlockmgr
     100021    3   udp   9027  nlockmgr
     100021    4   udp   9027  nlockmgr
     100021    1   tcp   9028  nlockmgr
     100021    3   tcp   9028  nlockmgr
     100021    4   tcp   9028  nlockmgr
Last updated on
Was this page helpful?